Call Today

 

How do you actually feel when it comes to How to Install a Bathtub?

Setting up a bathtub isn't specifically brain surgery, but it does require strong plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bath tub with a brand-new one is likewise a moderately hard job. If the old bathtub is readily accessible, the job can move quickly; if you have to open a wall surface to eliminate the old bathtub and also place the brand-new tub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will certainly need an assistant to leave the old bathtub and also set in the new one. See to it you have qualified on your own for the work and also are comfortable attempting it. Instead of employing a service provider to take over a halfway-completed project, it is better to consider using one before you start. Possibilities are you might need an expert plumber to make tube connections.
This write-up will certainly help you install a new bath tub in your restroom if you have actually already gotten a new tub and also don't require to change the plan of your previous supply of water pipelines.
Your tools and also material list need to comprise the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Planning for the Installation

To start with, the supporting frame supplied with the bathroom needs to be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the versatile faucet adapters to the bottom of the two faucets using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its last setting.

 

 

Removing Old Touches

If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water system. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be fairly problematic as a result of the restricted gain access to that is usually the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipes have been gotten rid of, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming during this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Before moving on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.

 

 

Mounting the Bath tub

Using both wooden boards under its feet, position the tub in the needed setting. The wood boards are handy in equally spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub until the level reviews level.
To mount taps, fit all-time low of the furthest versatile tap port to the ideal supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system as well as check all joints and also brand-new pipework for leaks and also tighten them if needed. Fill up the bath tub as well as also examine the overflow outlet and also the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the supplier's instruction manual. Tiling as well as securing around the tub needs to wait until the tub has actually been made use of at least when as this will certainly settle it into its last placement.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, then you will require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the current supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin making sure that the washers remain in place in between the tap and the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap adapters. The previous type should be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bath tub

In the location where the bath meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture a rigid seal, causing the water to permeate the wall surface between the bathroom and also the tiling, leading to issues with moisture as well as possible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your components as well as fittings. They are sold in tubes and also cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill the tub with water prior to sealing, to permit the movement experienced when the tub is in usage. The sealant can crack fairly very early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently available on the market. It is suggested to fit the tiles utilizing waterproof or water-proof adhesive and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We had been guided to that report on A Step-by-Step Guide to Installing a Bathtub from an associate on our other domain. In case you liked our blog post plz don't forget to share it. Kudos for your time. Visit again soon.

Give Me A Quote!